- Home
- NSN Catalog
- Hardware And Abrasives
- Nuts And Washers
- NSN 5310-00-754-1686
NSN 5310-00-754-1686
Flat WasherPricing & Availability Check
Submit this form for stock availability and pricing.Inventory
This product may be available in the following quantities and conditions.
- AR: 11
- NE: 1
Please note that inventory for this NSN was updated 03/23/2025 and may have changed since then. Request a quote for up to date pricing and availability.
Major End Items End items to which 5310-00-754-1686 is a component of
- A1N Close In Weapon System (ciws-phalanx)
- ACF B-1 Aircraft Support Equipment
- ADF Advanced Medium Range Air-to-air (amraam)/aim120a Missile
- AHN Fire Pumps
- AYA An/tyc-39a Central Message Switch
- BBN Phoenix (aim-54) Air-to-air Missile
- BDN Sparrow (aim-7) Air-to-air Missile
- BMN Mk 46 Torpedo Systems
- BYN An/uya-4(v) Tactical Data System
- N/A Turbine Engine Accessory Drive Gearbox
- N/A Circuit Card Assembly
- N/A Turbine Engine Gearbox Housing
- N/A Aircraft Mounted Winch
- N/A Auxiliary Power Sup
- N/A Radar Signal Simulator
- N/A Aircraft Electrical Power Control Assembly
- N/A Head-up Display Unit
- N/A Center-aft Section
- N/A Cimbal And Torquer
- N/A Countermeasures Dispenser Subassembly
- N/A Prima Cell Assembly
- N/A Lever Control Handle
- N/A Control Lever
- N/A Aircraft Coolant Fluid Tank
- N/A Rotary Pump
- N/A Selector Rotary Valve
- N/A Communication Equipment Interface Unit
- N/A Servocylinder
- N/A Message Swi Central
- N/A Nonexpandable Shelter
- N/A Aircraft Cabin Air Pressure Regulator
- N/A Turbine Engine Main Fuel Control
- N/A Training Guided Missile
- N/A Aircraft Centrifugal Clutch Assembly
- N/A Electronic Systems Test Set
- N/A Rocket Motor Cover
- N/A Guided Missile Transporter-erector
- N/A Aircraft Gun Drive Unit
- N/A Guided Missile Guidance And Control Section
- N/A Jet Engine Fuel Pump
- N/A Telephone Set
- N/A Gearcase-motor
- N/A Direct Current Motor
- N/A Warehouse Wheeled Tractor
- N/A Test Set Module Nav
- N/A Ground Handling Equipment Adapter
- N/A Power Supply
- N/A Pne Control Monitor
- N/A Electrical Cable Assembly Set
- N/A Electronic Equipment Air Cooler
- N/A Aircraft Mechanical Actuator
- N/A Linear Electro-mechanical Actuator
- N/A Aircraft Air Cycle Refrigeration Unit
- N/A High Explosive Guided Missile Warhead Section
- N/A Gas Turbine Engine Generator Set
- N/A Voice Terminal
- N/A Air-antitank Defense Missile System Carrier
- N/A Turret Struct Assy
- N/A Radio Frequency Rotary Coupler
- N/A Fluid Pressure Regulating Valve
- N/A Aircraft Maintenance Fixture
- N/A R Mounting Platform
- N/A Switch Assembly
- N/A Mechanical Drive Housing
- N/A Inverter
- N/A Steering Gearbox Assembly
- N/A Quadrant Lever
- N/A Warehouse Crane Truck
- N/A Alternating Current-direct Current Generator
- N/A Pressure Transmitter
- N/A Guided Missile System Radar Signal Simulator Station
- N/A Generator Control
- N/A Radar Transmitter
- N/A Aircraft Nosewheel Steering Unit
- N/A Unl Mechanical Tool
- N/A Air Conditioner
- N/A Electronic Warfare Training Set
- N/A Antenna Drive
- N/A Power Supply Assembly
- N/A Angle Drive Unit
- N/A Branched Electrical Special Purpose Cable Assembly
- N/A Chassis Assembly
Cross Reference Parts Part numbers that meet the specification outlined on this page and set by the OEM
Definition Definition of approved item name (AIN): "WASHER,FLAT"
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use shim. For items fabricated from ceramic or electrically rated materials by specification or industry standards use insulator (1), washer. Excludes disk, valve, graphite impregnated and lubricated items.
Identification Item Identification Guide (IIG) and Item Name Code (INC)
Special material and handling
Indicates there is no data in the hmirs and the nsn is in a fsc not generally suspected of containing hazardous materials.
Precious metal content is unknown
The item does not have a nuclear hardened feature or any other critical feature such as tolerance, fit restriction or application.
Import and Export
Schedule B Codes Definitions:
Washers Other Than Lock Washers, Iron Or Steel
Finished Metal Shapes
Screws, Bolts, Nuts, Screw Hooks, Rivets, Washers and Similar Articles, Not Threaded, Of Iron Or Steel
National motor freight and handling
Freight Codes Definitions:
No special type of cargo code applicable.
Metal hardware.
Construction materials: includes paint and related materials, prefabricated building, wood products, metal and composition mater.
Shipment is not a consolidation and does not exceed 84 inches in any dimension.
Other or no special handling required (sh)
DLA Forecast / History
Industrial Hardware Supply Chain03/2016 |
---|
47600.00 |